online posts 16
wireless 101: how wi-fi signal really travels

lesson 2.1 · chapter 2 of 7: bands and channels · 25 min

Bands and channels: 2.4, 5 and 6 GHz

objective

Name Wi-Fi’s three bands and what each is good at, explain why 2.4 GHz has only three channels that don’t overlap (1, 6 and 11), and pick channels and a channel width for six access points so neighbors don’t step on each other.

1 explain

Why does Wi-Fi have channels?

Lanes on a road

A band is a road, and channels are its lanes. If two cars try to use the same lane at the same moment, one has to wait. If a car straddles two lanes, it gets in everyone’s way. Wi-Fi’s whole channel story is about keeping access points that are near each other in lanes of their own.

in one sentence A band is the road; channels are its lanes.

Three bands

Wi-Fi uses three bands. Each has a trade-off:

BandIn the USGood atNot so good at
2.4 GHz2,400 to 2,483.5 MHzreaching farther and through wallsonly 3 clear channels; shared with Bluetooth and microwave ovens
5 GHzabout 5,150 to 5,850 MHzlots of channels; much less crowdeda little shorter reach; some channels need DFS
6 GHz5,925 to 7,125 MHzhuge and empty: 59 channels at 20 MHzshortest reach; only Wi-Fi 6E and Wi-Fi 7 devices can use it

Which devices can use which band depends on their Wi-Fi generation:

NameStandardBands
Wi-Fi 4802.11n2.4 and 5 GHz
Wi-Fi 5802.11ac5 GHz
Wi-Fi 6802.11ax2.4 and 5 GHz
Wi-Fi 6E802.11axadds 6 GHz
Wi-Fi 7802.11be2.4, 5 and 6 GHz, and wider channels

802.11 is the family of IEEE standards behind Wi-Fi; the letters after it are the version.

in one sentence 2.4 GHz reaches farthest, 5 GHz has the room, 6 GHz is wide open but only for newer devices.

Channels: numbers 5 MHz apart

A channel number names a spot in the band, and the numbers are only 5 MHz apart. On 2.4 GHz, channel 1 is centered on 2,412 MHz, channel 2 on 2,417, channel 6 on 2,437, and channel 11 on 2,462.

But a Wi-Fi signal is about 20 MHz wide. So channel 1 spreads from about 2,402 to 2,422 MHz, and channel 3 (2,422 MHz in the middle) lands right on top of half of it. To get completely clear of channel 1 you have to jump to channel 6, and then to 11. That’s why you’ll hear 1, 6 and 11 over and over: in the US, they’re the only three 2.4 GHz channels that don’t overlap.

On 5 and 6 GHz the channel numbers go up in steps of 4 (36, 40, 44…), which is exactly 20 MHz, so neighboring 20 MHz channels sit side by side without overlapping.

in one sentence Channel numbers are 5 MHz apart but signals are 20 MHz wide. On 2.4 GHz only 1, 6 and 11 stand clear.

Sharing a channel versus overlapping

Two access points near each other can relate in three ways:

  • Different, clear channels: they don’t affect each other at all. Best.
  • The same channel: Wi-Fi radios listen before they talk. Each one hears the other and waits its turn, so they share the airtime: each gets roughly half. Not great, but orderly. Engineers call it co-channel interference.
  • Partly overlapping channels (like 1 and 3): each hears the other as noise it can’t decode, so it doesn’t wait. They talk over each other, frames get garbled and resent, and both slow down. This is the worst case: adjacent-channel interference.

in one sentence Same channel: they take turns. Overlapping channels: they trample each other. Overlap is worse.

Channel width: faster, but fewer

A radio can bond neighboring 20 MHz channels into one wider channel, 40, 80 or 160 MHz (and 320 MHz on 6 GHz with Wi-Fi 7). A channel twice as wide carries about twice as much data. But:

  • it uses up the band twice as fast, so there are half as many clear channels to go around;
  • it catches twice as much noise, which raises the noise floor by 3 dB.
Width2.4 GHz5 GHz (US)6 GHz (US)
20 MHz32559
40 MHz1, really1229
80 MHznone614
160 MHznone27

In an office full of access points, 20 or 40 MHz on 5 GHz is the usual choice: enough clear channels that neighbors don’t have to share. A home with one access point can happily use 80 MHz.

in one sentence Wider channels are faster but fewer, and a little noisier. Busy places use narrower channels.

DFS: sharing with radar

On 5 GHz, channels 52 to 144 sit in bands also used by weather and military radar. An access point may use them only if it does DFS (dynamic frequency selection): it listens for radar for a while before it starts, and if it ever hears radar, it has to leave the channel and stay off it for half an hour. Clients on that access point get moved without warning. DFS channels more than double the clear 5 GHz channels, which is why most designs use them, but near an airport or a weather station they’re worth avoiding.

in one sentence DFS channels give 5 GHz most of its room, but an access point must give them up to radar.

2 show

The channel strip

The tool below draws a band as a strip of frequencies, from low on the left to high on the right, with tick marks for each channel number. Each access point gets a lane with a colored block showing exactly which frequencies its channel covers.

  • A block with a red outline partly overlaps another access point’s channel.
  • A block with a dashed amber outline shares a channel with another access point.
  • On 5 GHz, the shaded parts are the four sub-bands, and the amber ones need DFS.

Under the strip, the tool counts how many channels of the chosen width fit without overlapping, and lists every pair of access points that share or overlap.

in one sentence One lane per access point; red is overlap, amber is sharing.

3 follow along

Fix six access points

This tool needs JavaScript. The text below covers the same ideas.

Try these, in order:

  1. The six access points start on 2.4 GHz on channels 1, 3, 6, 6, 9 and 11. Six pairs partly overlap. Look at AP 2 on channel 3: its block covers half of channel 1’s and half of channel 6’s.
  2. Move AP 2 to 11 and AP 5 to 1. Now every access point is on 1, 6 or 11. Nothing overlaps, but three pairs share a channel: with six access points and three clear channels, some have to share. In a real building you’d make sure the ones sharing are far apart.
  3. Switch to 5 GHz at 20 MHz: 25 clear channels, plenty for six access points.
  4. Change the width to 80 MHz: 6 clear channels. Then 160 MHz: only 2, and both include DFS channels.
  5. Switch to 6 GHz: 7 clear channels even at 160 MHz.

in one sentence On 2.4 GHz you run out of clear channels fast. On 5 and 6 GHz the width you pick decides how many you get.

4 challenge

A row of six classrooms

A school corridor has six classrooms in a row, one access point in each. Each access point can hear its neighbors on either side, but not the ones two rooms away.

  1. Pick 2.4 GHz channels so that no two neighbors share or overlap.
  2. Pick 5 GHz channels at 40 MHz for the same six rooms. The school is next to a regional airport, so it wants no DFS channels.
hint

On 2.4 GHz you only have 1, 6 and 11. The rule is only about neighbors: rooms two apart can reuse a channel.

hint

Without DFS, 5 GHz keeps UNII-1 (36 to 48) and UNII-3 (149 to 165). At 40 MHz that’s 36-40, 44-48, 149-153 and 157-161.

show the solution
  1. 1, 6, 11, 1, 6, 11. Every neighbor is on a different clear channel. Rooms 1 and 4 share channel 1, but they’re three rooms apart and can’t hear each other.
  2. 36-40, 44-48, 149-153, 157-161, 36-40, 44-48. Four non-DFS 40 MHz channels for six rooms, so two get reused, again only by rooms far apart.

The pattern, reuse a channel only where the access points can’t hear each other, is the heart of channel planning. Lesson 5 shows how far an access point’s signal actually reaches, which tells you how far apart “can’t hear each other” needs to be.

Back to lesson 1 for dB and dBm, or on to lesson 3, where the antenna decides which way the signal goes. The listen-before-talk idea is close to the hub from Networking 101’s lesson 2.1: one shared medium, one talker at a time.

5 check: test yourself

Pick an answer for each question. You'll see straight away whether it's right, and why. Questions marked what happens next? are about the animations.

  1. In the US, which three 2.4 GHz channels don’t overlap each other?

  2. what happens next?Two access points near each other are on channels 1 and 3. Why is that worse than both on channel 1?

  3. You switch a 5 GHz design from 20 MHz to 80 MHz channels. What happens?

  4. What does an access point have to do before it uses a DFS channel?

  5. A laptop only supports Wi-Fi 6, not 6E. Which bands can it use?