lesson 1.1 · chapter 1 of 7: radio basics · 25 min
Radio basics: waves, dB and dBm
objective
Say what a radio wave’s frequency and wavelength are, count signal in dB and dBm (+3 dB doubles, +10 dB is ten times), and read a signal like −67 dBm and an SNR like 28 dB and know whether they’re good enough.
What is a Wi-Fi signal?
Ripples in a pond
Drop a stone in a pond and ripples spread out in rings. They get weaker as they spread, because the same energy is shared out over a bigger and bigger ring. They bounce off the bank, and they pass around a reed but not through a rock.
A Wi-Fi signal is a ripple too, but in the electric and magnetic field around an antenna instead of in water. It’s a radio wave, the same kind of thing as FM radio, phone signal and the light from a lamp, just at a different speed of wiggle. Everything this course covers is the pond: how the ripples spread, fade, bounce and get blocked.
in one sentence A Wi-Fi signal is a radio wave spreading out from an antenna, like ripples in a pond.
Frequency and wavelength
Two numbers describe a wave:
- Frequency: how many times it wiggles each second. One wiggle a second is one hertz (Hz). Wi-Fi wiggles billions of times a second: gigahertz (GHz). Wi-Fi uses three bands of frequencies, around 2.4 GHz, 5 GHz and 6 GHz (lesson 2 is all about them).
- Wavelength: how far apart the ripples are. Radio waves all travel at the speed of light, so the faster the wiggle, the shorter the wave.
| Band | Frequency | Wavelength |
|---|---|---|
| 2.4 GHz | 2,437 MHz (channel 6) | 12.3 cm, about 5 inches |
| 5 GHz | 5,180 MHz (channel 36) | 5.8 cm, about 2¼ inches |
| 6 GHz | 6,135 MHz (channel 37) | 4.9 cm, about 2 inches |
The wavelength matters more than you’d think. An antenna is usually about half a wavelength long, which is why 5 GHz antennas are shorter. And a shorter wave is easier to stop with a wall, which you’ll see in lesson 4.
in one sentence Frequency is wiggles per second; wavelength is the distance between ripples. Higher frequency, shorter wave.
Why decibels?
An access point sends about a tenth of a watt, less than a night light. By the time it reaches a laptop across the office, there’s about 0.00000001 milliwatts left: a hundred-millionth of a milliwatt. Numbers like that are miserable to work with. So engineers use decibels (dB), which count how many times bigger or smaller:
- +3 dB is twice the power; −3 dB is half.
- +10 dB is ten times; −10 dB is a tenth.
- +20 dB is a hundred times, +30 dB a thousand.
The magic is that multiplying becomes adding. An antenna that focuses the signal 2.3 times, and a wall that lets through a third of it, become +3.7 dB and −4.8 dB. Add them up and you have the answer.
in one sentence dB counts “how many times”: +3 dB doubles, +10 dB is ten times, and you add instead of multiply.
dBm: decibels against a milliwatt
A plain dB is a change. To say how strong a signal is, you need a starting point. dBm means decibels compared with one milliwatt:
| dBm | Power | Where you’d see it |
|---|---|---|
| 30 dBm | 1 W | the most the US allows at 2.4 GHz, before the antenna |
| 20 dBm | 100 mW | a home router turned all the way up |
| 0 dBm | 1 mW | the reference point |
| −30 dBm | 1 µW (a millionth of a watt) | a laptop right next to the access point |
| −67 dBm | about 0.2 nW | the usual target for voice and video calls |
| −95 dBm | about 0.3 pW | the noise floor: the radio hiss everywhere |
Signals at a laptop are almost always negative. Closer to zero is stronger: −50 dBm is a great signal, −80 dBm is a poor one.
in one sentence dBm is power compared with 1 mW. At the laptop it’s negative, and closer to zero is better.
RSSI, noise and SNR
Your laptop reports the strength it hears as RSSI (received signal strength indicator). On most laptops and phones you can see it in dBm (lesson 4 shows how), though some show a percentage or bars instead, and every maker scales those differently. dBm is the number engineers trust.
A strong signal isn’t enough on its own; it has to stand out from the noise, the background hiss from other electronics and from physics itself. The gap between them is the signal-to-noise ratio (SNR), and in dB it’s just a subtraction:
SNR = signal − noise = −67 dBm − (−95 dBm) = 28 dB
The more SNR, the faster the connection can go, because the radio can pack more bits into each wiggle without mistaking noise for data. Around 25 dB or more is comfortable for voice and video calls.
in one sentence RSSI is how loud the access point is; SNR is how much louder than the noise. Aim for −67 dBm and 25 dB.
From the access point to the laptop
Every Wi-Fi link is a chain of gains and losses. Engineers call the sum a link budget:
| Step | What happens | Typical |
|---|---|---|
| Transmit power | what the access point’s radio puts out | 14 to 20 dBm |
| Cable | a little lost between the radio and the antenna | −1 dB |
| Antenna gain | the antenna focuses the signal toward you (lesson 3) | +2 to +10 dBi |
| The air | the signal spreads out over distance (lesson 4) | −60 to −80 dB |
| Walls | each one takes a share (lesson 4) | −3 dB to −30 dB each |
| The laptop’s antenna | small, and not pointed anywhere in particular | about 0 dBi |
Two words worth knowing from that table:
- dBi: an antenna’s gain, compared with an imaginary antenna that sends the same amount in every direction. Lesson 3 explains it.
- EIRP (effective isotropic radiated power): transmit power, minus the cable, plus the antenna gain. It’s what actually leaves the antenna in its best direction, and it’s what regulators limit.
Start at the transmit power, add the gains, subtract the losses, and what’s left is the RSSI at the laptop.
in one sentence Signal at the laptop = transmit power − cable + antenna gain − air − walls. That’s a link budget.
Climb down the dB ladder
The top half converts between mW and dBm. The bottom half is a link budget, drawn as a staircase from the access point down to the laptop.
This tool needs JavaScript. The text below covers the same ideas.
Try these, in order:
- Set the power to 20 dBm (100 mW). Press +3 dB: 200 mW. Press it again: 400 mW. Now +10 dB from 20 dBm: 1,000 mW, a whole watt.
- In the link budget, the default is a 17 dBm access point with 1 dB of cable and a ceiling antenna (+3.7 dBi), 40 ft away on 5 GHz. The laptop gets about −49 dBm: an excellent signal.
- Drag the distance to 80 ft. The signal drops by about 6 dB: twice the distance costs 6 dB in open air.
- Add a drywall wall: −4 dB. Add poured concrete: about −26 dB. Watch the staircase fall below the green −67 dBm line.
- Switch the band to 2.4 GHz. The signal climbs a long way: the air costs about 6.5 dB less, and the concrete about 11 dB less. Lesson 4 explains why.
in one sentence Each step on the ladder is a dB you can add or subtract. The staircase ends at the RSSI.
Is it good enough for a video call?
A café’s access point sends 20 dBm through 2 dB of cable into a 6 dBi omni antenna. A customer sits where the air costs 75 dB and one brick wall (6 dB on 2.4 GHz) is in the way. Their laptop’s antenna counts as 0 dBi, and the noise floor is −95 dBm.
- What’s the access point’s EIRP?
- What’s the RSSI at the laptop?
- What’s the SNR, and is it good enough for a video call?
- How many dB would the café need to find to hit −67 dBm?
hint
EIRP is transmit power, minus the cable, plus the antenna gain.
hint
RSSI is the EIRP, minus the air, minus the walls, plus the laptop’s antenna gain.
show the solution
- EIRP = 20 − 2 + 6 = 24 dBm (about 250 mW).
- RSSI = 24 − 75 − 6 + 0 = −57 dBm.
- SNR = −57 − (−95) = 38 dB. Comfortably good enough for a video call.
- None: −57 dBm is already 10 dB better than the −67 dBm target. They have headroom for a second wall, or a few more tables farther away.
Turning the power up isn’t always the answer anyway. The laptop has to answer back with its own, weaker radio, and lesson 5 explains why a loud access point and a quiet laptop make a lopsided conversation.
Next: lesson 2 cuts the bands into channels. If any of the network words here are new, Networking 101’s lesson on hosts is the place to start.
5 check: test yourself
Pick an answer for each question. You'll see straight away whether it's right, and why. Questions marked what happens next? are about the animations.
An access point sends 100 mW. What’s that in dBm?
0 dBm is 1 mW. Each +10 dB is ten times: 10 mW is 10 dBm, 100 mW is 20 dBm.
You turn an access point up by 3 dB. What happened to its power?
+3 dB is twice the power, whatever you started from: 50 mW to 100 mW, or 1 W to 2 W.
Which is the stronger signal at a laptop: −50 dBm or −80 dBm?
Closer to zero is stronger. −50 dBm is 30 dB stronger than −80 dBm: a thousand times more power.
A laptop hears its access point at −70 dBm and the noise at −95 dBm. What’s the SNR?
SNR is signal minus noise: −70 − (−95) = 25 dB. In dB, dividing becomes subtracting.
what happens next?Why do wireless engineers count in dB at all?
A link budget becomes a sum: transmit power, plus antenna gain, minus losses. Try doing that in milliwatts.